Skip to content

Deye 5/6/12 kW Inverter Setup: Wiring, BMS & Time of Use

Deye 5/6/12 kW Inverter Setup: Wiring, BMS & Time of Use

Deye 5/6/12 kW Hybrid Inverter Setup & Wiring: Start Here

To commission a Deye 5 kW, 6 kW, or 12 kW low-voltage hybrid inverter without nuisance trips or unintended grid export, start with four physical and software checks before tweaking advanced menus: separate the GRID / LOAD / GEN AC circuits, verify LiFePO4 BMS wiring (CAN Pins 4–5, Lithium Mode 00), clamp the CT sensor with its arrow pointing toward the inverter, and configure Zero Export + Time of Use. Always tap the Enter (checkmark) button on every touchscreen page, otherwise changes are discarded.

Installer Quick-Start Summary: 1) Wire utility mains to GRID, backup circuits to LOAD, and generator or Smart Load to GEN. 2) For closed-loop LiFePO4 batteries with CAN cable, set Lithium, protocol 00 (Deye / Pylontech standard), and Use Batt %; use Use Batt V only for open-loop DIY packs. 3) Clamp the CT onto the incoming main phase wire with the arrow pointing toward the inverter. 4) In System Work Mode, choose Zero Export to CT (or Zero Export to Load if all loads are on LOAD), keep Zero-export Power = 20 W, and tick Time Of Use. 5) In Grid Setting for EU/Ukraine grids, set 230 V / 50 Hz and Reconnection Time = 60 s.

1. Deye 5 kW, 6 kW & 12 kW Models: Key Hardware Specs

The most widely deployed 48 V low-voltage models in our Deye hybrid inverter catalog share an IP65 enclosure, 4 ms UPS transfer time, 2 MPPT trackers for solar panels, and a 40–60 V DC battery window. See also our Deye hybrid inverter review and Deye pros and cons guide.

Model (Series)Phase & Rated ACMax Charge / DischargeRecommended Breakers (Manual)Key Highlight
Deye SUN-5K-SG05LP1-EU (and SG03LP1)1-phase, 5 kW120 A / 120 ADC Batt ~150 A, AC GRID/LOAD 32–40 ACompact residential 1-phase backup
Deye SUN-6K-SG05LP1-EU (and SG03LP1)1-phase, 6 kW135 A / 135 ADC Batt ~160 A, AC GRID/LOAD 40 AMost popular 1-phase model (Deye 6 kW); higher-power sibling SUN-8K-SG05LP1-EU
Deye SUN-12K-SG04LP3-EU3-phase, 12 kW240 A / 240 ADC Batt 300 A, AC GRID 63 A, LOAD 32–63 A100% unbalanced 3-phase output (up to 50% rated power / 6 kW per phase), 12 kW inverters

Matched 48 V storage options include Deye batteries such as the rack-mount Deye SE-G5.1 Pro-B (5.12 kWh) and wall-mount Deye RW-F16 (16 kWh), alongside our wider LiFePO4 battery catalog.

2. Pre-Installation Checklist

  • Load-bearing wall & clearance: Anchor the wall bracket into masonry or concrete (6 kW weighs ~20–25 kg; 12 kW exceeds 33 kg) with full airflow clearance around the heatsink.
  • Manual 1-0-2 bypass switch: Install a manual changeover switch (e.g., 40 A) and clearly labeled breakers for Grid, To Inverter, From Inverter, and Generator so the house stays powered during maintenance.
  • DC battery protection & lugs: High 48 V currents (120–240 A) require properly sized DC breakers/fuses (300 A DC recommended for SUN-12K-SG04LP3-EU) and hydraulically crimped copper lugs.
  • Grounding & ferrite beads: Bond PE to inverter chassis, AC busbars, and PV frames. Loop AC conductors, CT wires, and the BMS RJ45 cable through the supplied white ferrite beads inside the wiring bay to suppress EMI.

3. Wiring GRID, LOAD, GEN, LiFePO4 BMS & CT Sensor

Isolate all AC, DC battery, and PV disconnects before opening the lower wiring compartment.

  • GRID: Main utility supply after the meter and main breaker.
  • LOAD (Backup): Critical circuits powered without interruption (4 ms transfer) during outages. Keep total backup demand within rated limits to prevent F18 / F20 trips.
  • GEN: Configurable via Gen Port Use as Generator Input (dry-contact auto-start on G-start: 5,6), SmartLoad Output (excess solar dump), or Micro Inv Input (AC-coupling with AC Couple Frz High: 52.00 Hz).
  • LiFePO4 BMS (CAN): Verify polarity on BAT+ / BAT- with a multimeter. Connect the inverter BMS 485/CAN port to the master battery CAN port. Deye standard CAN pinout uses Pin 4 = CAN-H and Pin 5 = CAN-L.
  • CT Sensor Orientation: Clamp the split-core CT around the incoming main phase wire only (three CTs on L1/L2/L3 for 12 kW) upstream of non-backup home loads. Per the official Deye manual, the arrow on the CT must point toward the inverter. Wire leads to CT-3,4 and verify CT Ratio = 2000:1 under Advanced Function.

4. Safe First-Start Commissioning Sequence

  1. Install the Wi-Fi/RS232 logger under the top cover while de-energized.
  2. Close the DC battery breaker and power on the LiFePO4 battery pack.
  3. Press the side ON/OFF button on the inverter (blue LED lights up) and wait for the LCD to boot.
  4. Configure date/time, Battery Setting, Grid Setting, and Work Mode, tapping Enter on each screen.
  5. Close the GRID breaker, wait 60 seconds for grid synchronization (green AC and Normal LEDs), then close LOAD and PV disconnects.
  6. Simulate an outage by switching off the main Grid breaker under 0.5–1 kW load to verify instant 4 ms battery transfer.

5. Firmware-Dependent Menu Differences

  • Classic paged UI (SG03 / early SG05): Uses Battery Setting Pages 1–3 and System Work Mode Pages 1–3.
  • Vertical-scroll UI (newer SG05 / OG01): Groups settings under Battery Setup → Batt Set1 / Batt Set2 / Batt Set3.
  • Post-OTA firmware additions (2025–2026): Remote OTA updates via Deye support add Bat Supply@Grid Cut, Disable Tou When grid Off (ignores Time of Use discharge limits during blackouts), and Enable grid start value with Start % and Grid charge stop % thresholds.

6. Core Menu Parameters Reference

ParameterRecommended SettingNotes
Batt ModeLithium + Use Batt %Closed-loop CAN/RS485; choose Use Batt V only for open-loop DIY packs
Lithium Mode00Native Deye (SE-G5.1 Pro-B, RW-F16) and Pylontech CAN protocol
Max A Charge / DischargeWithin BMS & inverter limitsCap at 120 A (5 kW), 135 A (6 kW), 240 A (12 kW); 40–60 A charge reduces fan noise and cell heating
Shutdown / Low Batt / RestartManual: 10% / 20% / 40%; outage reserve: 15–20% / 30–35% / 45–50%Higher field thresholds preserve LiFePO4 longevity during frequent outages
Work ModeZero Export to CT or Zero Export to LoadKeep Zero-export Power = 20 W; disable Solar Sell without an export tariff; use Batt First when grid reliability is low
Time Of Use (6 slots)Time Of Use ✓Tick Grid in off-peak slots to charge up to target Batt %; untick Grid in daytime slots to discharge down to target SOC
Grid SettingGeneral Standard, 230 V, 50 Hz, Rec. Time 60 sSome videos select 220 V, but EU/Ukraine standard and Deye EU manual specify 230 V / 50 Hz
BMS_Err_Stop✓ (Advanced Function)Stops inverter with F58 if BMS link drops, preventing blind overcharge/overdischarge

7. Deye Fault Codes: F56, F58, F18, F20, F26, F35 & F13

CodeManual MeaningCommon Field CausesTroubleshooting Steps
F56DC_VoltLow_Fault (Low DC bus / battery voltage)Battery below Shutdown, tripped DC breaker, BMS protection lock, voltage drop on undersized/loose cablesMeasure BAT+/BAT- voltage (40–60 V), inspect DC breaker & BMS LEDs, torque terminals, recharge via Grid/PV
F58BMS Communication FaultBMS_Err_Stop active while CAN/RS485 cable is loose, wrong pinout, or wrong Lithium ModeVerify CAN cable on BMS 485/CAN (Pins 4–5), set Lithium Mode = 00, or disable BMS_Err_Stop for temporary fallback
F18AC Overcurrent Fault (Hardware)Heavy startup surge or short circuit on LOAD portShed heavy backup loads, check LOAD wiring for shorts, restart inverter
F20DC Overcurrent Fault (Hardware)Heavy off-grid startup surge or PV/battery DC wiring issueReduce off-grid startup loads, inspect PV and battery DC lines
F26DC Busbar Unbalanced (3-phase)Severe phase imbalance on SUN-12K-SG04LP3-EU or transient DC leakageKeep single-phase loads within 50% rated power (6 kW per phase), power-cycle AC+DC
F35No AC GridUtility outage, tripped Grid breaker, or voltage/frequency out of 185–265 V / 48–51.5 HzNormal during blackouts; otherwise check Grid breaker and terminals
F13Working Mode ChangedGrid standard, battery mode, or firmware update appliedUsually auto-clears; otherwise power-cycle AC and DC for 1 minute

8. Sources & Verification

  • Official Ningbo Deye Inverter Technology documentation (deyeinverter.com): SUN-5K/6K-SG03/05LP1-EU and SUN-12K-SG04LP3-EU User Manuals, Datasheets, and Approved Battery List.
  • Field video references (4 YouTube donors): SDV channel (Deye SUN-6k menu), Вечно Занятой (OTA firmware update & new TOU/Grid functions), Геннадий Ларионов (SUN 6K menu setup), and Chudo Obzor (full 6 kW physical installation).

Technical specifications, CAN pinouts, charge/discharge limits, and fault codes are verified against official manufacturer documentation. Exact menu labels and OTA options vary by firmware revision.

Selecting a Deye Inverter & LiFePO4 Battery

Our catalog (in stock and available to order) carries Deye SUN-5K-SG05LP1-EU, SUN-6K-SG05LP1-EU, SUN-8K-SG05LP1-EU, the three-phase SUN-12K-SG04LP3-EU, and compatible SE-G5.1 Pro-B / RW-F16 packs. Browse our Deye hybrid inverters or contact our engineering team to size breakers, cabling, and storage capacity for your site.

⚡

Need a variable frequency drive for your motor?

We'll find the right solution by power, voltage and load type

Browse catalog Consultation

Поширені запитання

For factory LiFePO4 packs with a CAN/RS485 cable (such as Deye SE-G5.1 Pro-B or RW-F16), select Lithium, Lithium Mode 00, and Use Batt %. Choose Use Batt V only for open-loop DIY battery packs without BMS communication.