VI20-101S-F HMI Veichi VI20 Size 10.1in
Є в наявності
sku: VI20-101S-F
Є в наявності
17 200 UAH
brand: Veichi
Series: VI20
Panel type: графическая
Diagonal: 10.1 inch
Delivery and payment methods
By Nova Poshta to a branch or courier to the address
Bank transfer payment
Service and Warranty
- 24-month Warranty
- Product return within 14 days
- Official Service Center
Technical support
- Help with setup and selection
- Зацікавив товар?
Наш продавець проконсультує Вас.
- Characteristics
- Documentation
- Reviews (1)
| brand | Veichi |
| Series | VI20 |
| sku | VI20-101S-F |
| Replacement (If discontinued) | No |
| Panel type | графическая |
| Matrix type | TFT LCD |
| Diagonal | 10.1 inch |
| Chroma | 24bit |
| Width | 1024 mm |
| Height | 600 mm |
| number of ports | 3 |
| Interface | RS232/485/422, RS232 |
| Protocol | Modbus RTU |
| USB port | USB Slave/Host 2.0 |
| Additional | CPU: 600MHz ARM Cortex-A8, Memory: 128MB Flash+128MB DDR3, LED backlight, 400 cd/m², DC24V (9-28V) |
| Color rendering | Black |
Documents by language
Ukrainian / English / Russian
Chastotnik.ua
Practical setup guides
Chastotnik.ua materials for wiring and setup. These are not official manufacturer documents.
Guide
Replacing a European VFD with Veichi: NPN/PNP, PLC jumper, COM vs GND
The most common scenario when replacing a European drive (Schneider Altivar, Siemens, LS, Danfoss) with Veichi looks like this: the power section is w...
Go to
Guide
COM or GND: why the buttons do not work on a Veichi VFD
A typical picture after installation: the Veichi VFD starts from the keypad, the parameters are entered, but the external Start/Stop buttons produce n...
Go to
Guide
PLC jumper on Veichi: wiring PNP/NPN sensors and pushbuttons
On the control board of Veichi AC10 (from 7.5 kW) and AC310 three terminals sit side by side: +24V, PLC and COM. Between them is a small jumper. Its p...
Go to
Guide
VFD grounding and stray voltage on the enclosure (PE, >5V)
A fairly common complaint after installation: voltage "tingles" on the motor housing, the cabinet or the drive itself, while the keypad or sensors sta...
Go to
Guide
Shielding a 4-20mA sensor: which end to ground, 15 cm separation
A pressure or flow sensor in pump automation almost always outputs a 4-20 mA current signal. On Veichi it is wired to an analog input that can operate...
Go to
Guide
Replacing a Schneider Altivar with Veichi: step-by-step terminal and parameter migration
The power section of a Schneider Altivar and a Veichi is wired the same way: mains to R/S/T, motor to U/V/W, PE to the ground terminal. The difficulty...
Go to
Product Reviews
1
Overall rating
5.0
out of 5
1 reviews
5
1
4
0
3
0
2
0
1
0
�
Олег, інженер-автоматник
Взяв цю панель Veichi VI20-101S-F для заміни старої на виробничій лінії. Діагональ 10.1 дюйма, як раз те, що треба – все видно чітко. 24 біти кольору, матриця TFT LCD, тому картинка пристойна, не ріже око. Підключення через RS485 до контролера пройшло без проблем, Modbus RTU працює стабільно. Проц ARM Cortex-A8 на 600МГц і пам'ять 128MB Flash + 128MB DDR3 – для своїх задач панель досить шустра, не тупить. USB-порт теж плюс, зручно проекти закидати. За свої гроші варіант дуже гідний, Veichi як завжди тішить співвідношенням.
To leave a review, please, log in.
This page contains information about
HMI Veichi VI20 Size 10.1in ( VI20-101S-F )
with a detailed description of the technical characteristics
.
You can download
documentation for VI20-101S-F, series VI20 from manufacturer Veichi
.
Buy VI20101SF
and seek technical advice.
Our Engineers will help you choose and buy
VI20-101S-F only high quality at affordable prices. Guarantee.
VI20-101S-F
