Skip to content

SD700-8R4D-SA Servo drive 2.6kW 380V 8.4A Standard

Є в наявності
SD700-8R4D-SA Servo drive 2.6kW 380V 8.4A Standard
Клікніть для збільшення
Veichi
Є в наявності
40 869 UAH
Brand: Veichi
Series: SD700
Power: 2.6 kW
Servo type: Servo drive

delivery-iconDelivery and payment methods

  • Nova Poshta OfficeBy Nova Poshta to a branch or courier to the address
  • OplataBank transfer payment

delivery-iconService and Warranty

  • 24-month Warranty
  • Product return within 14 days
  • Official Service Center

delivery-iconTechnical support

  • Help with setup and selection
  • Interested in this product?
    Our specialist will advise you.
  • Write ⤵
    Telegram VIA TELEGRAM
    Write ⤵
    Viber VIA VIBER
  • Characteristics
  • Description
  • Documentation
  • Reviews (1)
Brand Veichi
Series SD700
SKU SD700-8R4D-SA
Power 2.6 kW
Current 8.40 A
Number of phases/input voltage 3-ф/380 V
Voltage 380 V
DI 8
AI 2
DO 4
AO 2
Encoder resolution 17/23-bit
Structure Standard type
Dimensions V
Servo type Servo drive
Video Thumbnail
Video Thumbnail
Documents by language

Ukrainian / English / Russian

Chastotnik.ua

Practical setup guides

Chastotnik.ua materials for wiring and setup. These are not official manufacturer documents.

Guide Replacing Delta VFD-EL with Veichi AC10: Migration Guide An engineering guide for retrofitting industrial systems by replacing obsolete Delta VFD-EL frequency inverters with modern Veichi AC10 drives. Contai... Go to Guide Replacing a European VFD with Veichi: NPN/PNP, PLC jumper, COM vs GND The most common scenario when replacing a European drive (Schneider Altivar, Siemens, LS, Danfoss) with Veichi looks like this: the power section is w... Go to Guide COM or GND: why the buttons do not work on a Veichi VFD A typical picture after installation: the Veichi VFD starts from the keypad, the parameters are entered, but the external Start/Stop buttons produce n... Go to Guide PLC jumper on Veichi: wiring PNP/NPN sensors and pushbuttons On the control board of Veichi AC10 (from 7.5 kW) and AC310 three terminals sit side by side: +24V, PLC and COM. Between them is a small jumper. Its p... Go to Guide VFD grounding and stray voltage on the enclosure (PE, >5V) A fairly common complaint after installation: voltage "tingles" on the motor housing, the cabinet or the drive itself, while the keypad or sensors sta... Go to Guide Shielding a 4-20mA sensor: which end to ground, 15 cm separation A pressure or flow sensor in pump automation almost always outputs a 4-20 mA current signal. On Veichi it is wired to an analog input that can operate... Go to
Product Reviews
1
5 1
4 0
3 0
2 0
1 0
О
Олег К.
★ ★ ★ ★ ★
26.02.2026

I bought this Veichi SD700 2.6 kW servo drive to replace the old one on a CNC milling machine. 380V connection, everything as it should be. I immediately noticed the compactness, it fit into the cabinet without any problems. The 17/23-bit encoder accuracy is just super, the machine now works noticeably smoother, without jerking, and the surface finish quality has improved. Programming it was not difficult, I even figured it out myself, and then the consultants also helped with fine-tuning. Veichi did not let me down, once again I am convinced that this is quality equipment for adequate money. Now my CNC just flies.

This page contains information about Servo drive 2.6kW 380V 8.4A Standard ( SD700-8R4D-SA ) with a detailed description of the technical characteristics . You can download documentation for SD700-8R4D-SA, series SD700 from manufacturer Veichi . Buy SD7008R4DSA and seek technical advice. Our Engineers will help you choose and buy SD700-8R4D-SA only high quality at affordable prices. Guarantee. SD700-8R4D-SA