SD100-800G-PNB Veichi SD100 low-voltage servo drive, 80A/240A, DC 24-72V, ProfiNet, IP67, for AMR/AGV mobile robots, special robots.
Є в наявності
sku: SD100-800G-PNB
Є в наявності
68 958 UAH
Brand: Veichi
Series: SD100
Family: SD100
Rated Power (W):
Voltage (V DC): 48.0
IP Rating: IP67
Communication: ProfiNet
Delivery and payment methods
By Nova Poshta to a branch or courier to the address
Bank transfer payment
Service and Warranty
- 24-month Warranty
- Product return within 14 days
- Official Service Center
Technical support
- Help with setup and selection
- Зацікавив товар?
Наш продавець проконсультує Вас.
- Characteristics
- Documentation
- Reviews (0)
| sku | SD100-800G-PNB |
| Brand | Veichi |
| Series | SD100 |
| Family | SD100 |
| Voltage (V DC) | 48.0 |
| Rated Current (A) | 80.00 |
| Peak Current (A) | 240.00 |
| Rated Speed (rpm) | 3000 |
| Communication | ProfiNet |
| IP Rating | IP67 |
| Application | AMR/AGV mobile robot, service robot, logistics sorting, medical equipment |
Documents by language
Ukrainian / English / Russian
Chastotnik.ua
Practical setup guides
Chastotnik.ua materials for wiring and setup. These are not official manufacturer documents.
Guide
Replacing a European VFD with Veichi: NPN/PNP, PLC jumper, COM vs GND
The most common scenario when replacing a European drive (Schneider Altivar, Siemens, LS, Danfoss) with Veichi looks like this: the power section is w...
Go to
Guide
COM or GND: why the buttons do not work on a Veichi VFD
A typical picture after installation: the Veichi VFD starts from the keypad, the parameters are entered, but the external Start/Stop buttons produce n...
Go to
Guide
PLC jumper on Veichi: wiring PNP/NPN sensors and pushbuttons
On the control board of Veichi AC10 (from 7.5 kW) and AC310 three terminals sit side by side: +24V, PLC and COM. Between them is a small jumper. Its p...
Go to
Guide
VFD grounding and stray voltage on the enclosure (PE, >5V)
A fairly common complaint after installation: voltage "tingles" on the motor housing, the cabinet or the drive itself, while the keypad or sensors sta...
Go to
Guide
Shielding a 4-20mA sensor: which end to ground, 15 cm separation
A pressure or flow sensor in pump automation almost always outputs a 4-20 mA current signal. On Veichi it is wired to an analog input that can operate...
Go to
Guide
Replacing a Schneider Altivar with Veichi: step-by-step terminal and parameter migration
The power section of a Schneider Altivar and a Veichi is wired the same way: mains to R/S/T, motor to U/V/W, PE to the ground terminal. The difficulty...
Go to
This page contains information about
Veichi SD100 low-voltage servo drive, 80A/240A, DC 24-72V, ProfiNet, IP67, for AMR/AGV mobile robots, special robots. ( SD100-800G-PNB )
with a detailed description of the technical characteristics
.
You can download
documentation for SD100-800G-PNB, series SD100 from manufacturer Veichi
.
Buy SD100800GPNB
and seek technical advice.
Our Engineers will help you choose and buy
SD100-800G-PNB only high quality at affordable prices. Guarantee.
SD100-800G-PNB
