SD710-7R6A Economic servo drive 1.5kW, 220V single/three-phase, 7.6A rated/22.8A peak current, Pulse type
Є в наявності
sku: SD710-7R6A
Є в наявності
22 695 UAH
Brand: Veichi
Series: SD710
Power: 1.5 kW
servo_type: servoset
Delivery and payment methods
By Nova Poshta to a branch or courier to the address
Bank transfer payment
Service and Warranty
- 24-month Warranty
- Product return within 14 days
- Official Service Center
Technical support
- Help with setup and selection
- Зацікавив товар?
Наш продавець проконсультує Вас.
- Characteristics
- Documentation
- Reviews (1)
Documents by language
Ukrainian / English / Russian
Chastotnik.ua
Practical setup guides
Chastotnik.ua materials for wiring and setup. These are not official manufacturer documents.
Guide
Replacing a European VFD with Veichi: NPN/PNP, PLC jumper, COM vs GND
The most common scenario when replacing a European drive (Schneider Altivar, Siemens, LS, Danfoss) with Veichi looks like this: the power section is w...
Go to
Guide
COM or GND: why the buttons do not work on a Veichi VFD
A typical picture after installation: the Veichi VFD starts from the keypad, the parameters are entered, but the external Start/Stop buttons produce n...
Go to
Guide
PLC jumper on Veichi: wiring PNP/NPN sensors and pushbuttons
On the control board of Veichi AC10 (from 7.5 kW) and AC310 three terminals sit side by side: +24V, PLC and COM. Between them is a small jumper. Its p...
Go to
Guide
VFD grounding and stray voltage on the enclosure (PE, >5V)
A fairly common complaint after installation: voltage "tingles" on the motor housing, the cabinet or the drive itself, while the keypad or sensors sta...
Go to
Guide
Shielding a 4-20mA sensor: which end to ground, 15 cm separation
A pressure or flow sensor in pump automation almost always outputs a 4-20 mA current signal. On Veichi it is wired to an analog input that can operate...
Go to
Guide
Replacing a Schneider Altivar with Veichi: step-by-step terminal and parameter migration
The power section of a Schneider Altivar and a Veichi is wired the same way: mains to R/S/T, motor to U/V/W, PE to the ground terminal. The difficulty...
Go to
Product Reviews
1
Overall rating
5.0
out of 5
1 reviews
5
1
4
0
3
0
2
0
1
0
�
Ігор, власник майстерні
Взяв собі цей сервопривід Veichi SD710 на 1.5 кВт для оновлення одного фрезерного ЧПУ верстата. До того стояв старий привід, вже нікуди. Цей серво - зовсім інша справа. На 220В працює без проблем, що мені важливо. Керування імпульсне, як і треба було. Головне - точність, з цим 17/23-бітним енкодером вісь тримає дуже добре, навіть при швидкій зміні напрямку. Обробка пішла набагато чистіше. Для своєї ціни (а Veichi добре балансує якість і вартість) це крутий варіант. Вже другий рік працює без нарікань)
To leave a review, please, log in.
This page contains information about
Economic servo drive 1.5kW, 220V single/three-phase, 7.6A rated/22.8A peak current, Pulse type ( SD710-7R6A )
with a detailed description of the technical characteristics
.
You can download
documentation for SD710-7R6A, series SD710 from manufacturer Veichi
.
Buy SD7107R6A
and seek technical advice.
Our Engineers will help you choose and buy
SD710-7R6A only high quality at affordable prices. Guarantee.
SD710-7R6A
