SD700-1R8A-PA Servo drive 0.2kW 220V 1.8A Pulse
Є в наявності
sku: SD700-1R8A-PA
Є в наявності
17 084 UAH
Brand: Veichi
Series: SD700
Power: 0.2 kW
servo_type: servoset
Delivery and payment methods
By Nova Poshta to a branch or courier to the address
Bank transfer payment
Service and Warranty
- 24-month Warranty
- Product return within 14 days
- Official Service Center
Technical support
- Help with setup and selection
- Зацікавив товар?
Наш продавець проконсультує Вас.
- Characteristics
- Documentation
- Reviews (1)
Documents by language
Ukrainian / English / Russian
Chastotnik.ua
Practical setup guides
Chastotnik.ua materials for wiring and setup. These are not official manufacturer documents.
Guide
Replacing a European VFD with Veichi: NPN/PNP, PLC jumper, COM vs GND
The most common scenario when replacing a European drive (Schneider Altivar, Siemens, LS, Danfoss) with Veichi looks like this: the power section is w...
Go to
Guide
COM or GND: why the buttons do not work on a Veichi VFD
A typical picture after installation: the Veichi VFD starts from the keypad, the parameters are entered, but the external Start/Stop buttons produce n...
Go to
Guide
PLC jumper on Veichi: wiring PNP/NPN sensors and pushbuttons
On the control board of Veichi AC10 (from 7.5 kW) and AC310 three terminals sit side by side: +24V, PLC and COM. Between them is a small jumper. Its p...
Go to
Guide
VFD grounding and stray voltage on the enclosure (PE, >5V)
A fairly common complaint after installation: voltage "tingles" on the motor housing, the cabinet or the drive itself, while the keypad or sensors sta...
Go to
Guide
Shielding a 4-20mA sensor: which end to ground, 15 cm separation
A pressure or flow sensor in pump automation almost always outputs a 4-20 mA current signal. On Veichi it is wired to an analog input that can operate...
Go to
Guide
Replacing a Schneider Altivar with Veichi: step-by-step terminal and parameter migration
The power section of a Schneider Altivar and a Veichi is wired the same way: mains to R/S/T, motor to U/V/W, PE to the ground terminal. The difficulty...
Go to
Product Reviews
1
Overall rating
5.0
out of 5
1 reviews
5
1
4
0
3
0
2
0
1
0
�
Володимир П.
Поставив цей сервопривід Veichi SD700 на свій невеликий фрезерний ЧПУ. Потужності 0.2кВт вистачає за очі, а головне – точність. 17-бітний енкодер робить свою справу, рухи стають дуже плавні, без ривків. До цього стояв старий кроковик, різниця колосальна. Сама серія SD700 компактна, що для моєї майстерні важливо, місця не так багато в шафі. Підключення було просте, протокол pulse type з моїм контролером завівся швидко. Техпідтримка від магазину теж норм, допомогли з пару питаннями по налаштуванню. Якість роботи тепер набагато вища.
To leave a review, please, log in.
This page contains information about
Servo drive 0.2kW 220V 1.8A Pulse ( SD700-1R8A-PA )
with a detailed description of the technical characteristics
.
You can download
documentation for SD700-1R8A-PA, series SD700 from manufacturer Veichi
.
Buy SD7001R8APA
and seek technical advice.
Our Engineers will help you choose and buy
SD700-1R8A-PA only high quality at affordable prices. Guarantee.
SD700-1R8A-PA
