SD600A-S2-R20-N SD600 Series 0.2KW
Є в наявності
sku: SD600A-S2-R20-N
Є в наявності
97 028 UAH
Brand: Veichi
Series: SD600
Power: 0.2 kW
servo_type: servoset
Delivery and payment methods
By Nova Poshta to a branch or courier to the address
Bank transfer payment
Service and Warranty
- 24-month Warranty
- Product return within 14 days
- Official Service Center
Technical support
- Help with setup and selection
- Зацікавив товар?
Наш продавець проконсультує Вас.
- Characteristics
- Documentation
- Reviews (1)
| Brand | Veichi |
| Series | SD600 |
| sku | SD600A-S2-R20-N |
| Power | 0.2 kW |
| Current | 1.60 A |
| Number of phases/input voltage | 1-ф/220В V |
| DI | 9 |
| AI | 2 |
| DO | 6 |
| AO | 0 |
| Encoder resolution | 2500 имп/об |
| Structure | RS-485, САNopen |
| rezistor | Встроенный |
| Dimensions | 139.5+75х62х162 |
| Programming | VeichiSoft |
| servomotor | {'SMM06-2TR10-U1NL5','SMM06-2TR20-U1NL5''} |
| revs | 3000 |
| servo_type | servoset |
Documents by language
Ukrainian / English / Russian
EN English
UA Ukrainian
Chastotnik.ua
Practical setup guides
Chastotnik.ua materials for wiring and setup. These are not official manufacturer documents.
Guide
Replacing a European VFD with Veichi: NPN/PNP, PLC jumper, COM vs GND
The most common scenario when replacing a European drive (Schneider Altivar, Siemens, LS, Danfoss) with Veichi looks like this: the power section is w...
Go to
Guide
COM or GND: why the buttons do not work on a Veichi VFD
A typical picture after installation: the Veichi VFD starts from the keypad, the parameters are entered, but the external Start/Stop buttons produce n...
Go to
Guide
PLC jumper on Veichi: wiring PNP/NPN sensors and pushbuttons
On the control board of Veichi AC10 (from 7.5 kW) and AC310 three terminals sit side by side: +24V, PLC and COM. Between them is a small jumper. Its p...
Go to
Guide
VFD grounding and stray voltage on the enclosure (PE, >5V)
A fairly common complaint after installation: voltage "tingles" on the motor housing, the cabinet or the drive itself, while the keypad or sensors sta...
Go to
Guide
Shielding a 4-20mA sensor: which end to ground, 15 cm separation
A pressure or flow sensor in pump automation almost always outputs a 4-20 mA current signal. On Veichi it is wired to an analog input that can operate...
Go to
Guide
Replacing a Schneider Altivar with Veichi: step-by-step terminal and parameter migration
The power section of a Schneider Altivar and a Veichi is wired the same way: mains to R/S/T, motor to U/V/W, PE to the ground terminal. The difficulty...
Go to
Product Reviews
1
Overall rating
5.0
out of 5
1 reviews
5
1
4
0
3
0
2
0
1
0
�
Ігор, власник майстерні ЧПУ
Взяли цей сервопривід Veichi SD600 на невеликий фрезер ЧПУ, 0.2 кВт потужності якраз вистачає для наших задач. Живлення від звичайної 1-фазної мережі, що зручно для майстерні. 3000 об/хв і роздільна здатність енкодера 2500 імп/об дають дуже гарну точність. Вбудований резистор теж плюс, не треба окремо нічого вигадувати. Завдяки RS-485 легко підключили до системи. Програмується через VeichiSoft, досить зрозуміло, налаштування та тюнінг пройшли без проблем. Вже не перший раз беремо Veichi, якість за їхню ціну завжди тішить. І розміри компактні, в шафу вписався ідеально. Роботою приводу задоволений)
To leave a review, please, log in.
This page contains information about
SD600 Series 0.2KW ( SD600A-S2-R20-N )
with a detailed description of the technical characteristics
.
You can download
documentation for SD600A-S2-R20-N, series SD600 from manufacturer Veichi
.
Buy SD600AS2R20N
and seek technical advice.
Our Engineers will help you choose and buy
SD600A-S2-R20-N only high quality at affordable prices. Guarantee.
SD600A-S2-R20-N
